KRAFTDXF

Guide

How to Resize a DXF Without Ruining It

Making a design bigger or smaller sounds like the simplest job in the workshop. It is also one of the easiest ways to ruin a cutting file: shrink a panel and every strip of steel in it shrinks too. This guide explains what really changes when you resize a DXF, the mistakes that scrap sheets, and how to resize safely.

What changes when you resize

Scaling multiplies every measurement in the drawing by the same number. Make a panel half as wide and everything is halved — including the parts you did not think about:

In the drawingAt 100%At 50%What it means
Panel width1000 mm500 mmWhat you wanted
Bridge between two cuts6 mm3 mmToo thin for 3 mm plate
Bolt hole6.5 mm3.25 mmAn M6 bolt no longer fits
Slot for a 3 mm tab3.2 mm1.6 mmThe tab no longer fits

The one thing that does not scale is your plate. A bridge has to be at least 2× the plate thickness whatever size the panel is. So a design that passes at one size can fail at a smaller one — and a file cannot tell you that unless something measures it again.

Five mistakes that scrap sheets

  1. Shrinking without re-checking the bridges. The most common one. The drawing still looks perfect on screen; the thin strips burn away on the machine.
  2. Stretching by accident. Scaling the width and the height by different amounts turns circles into ovals and squares into rectangles. Always scale both directions by the same factor unless you really mean to stretch.
  3. Mixing up units. A drawing made in inches and opened as millimetres comes out 25.4 times too small. If your part is suddenly tiny, this is almost always why. A good DXF states its units inside the file.
  4. Scaling fixed-size features. Bolt holes, tab slots and anything that must fit a bought part have to stay their real size. Resize the design, then put those features back to size.
  5. Scaling a kerf-adjusted file a long way. A cut-ready file already has the cutting width allowed for. Scale it a lot and that allowance is scaled too. For a big change, go back to the original design and make the file again at the new size.

How to resize safely

  1. Decide the size from one number — the new width, the new height, or a percentage — and let the other side follow.
  2. Measure the thinnest bridge again at the new size, for the plate you will actually cut.
  3. Check small openings: very small holes close up or cut as slits once the cutting width is taken out.
  4. Put fixed-size features (bolt holes, slots) back to their real size.
  5. Run the normal cut-ready checklist on the result.

How KraftDXF resizes

Every converted design in the KraftDXF app has a Resize box. Type a new width, a new height or a percentage and the other side follows with one exact factor, so the design keeps its shape — circles stay round. Then every cutting check is measured again at the new size: the thinnest bridge, islands, openness, weight, and every outline. Anything too small to cut at the new size is listed, never dropped silently. If the new size would leave the steel too thin for your plate, the tool refuses it and offers the smallest size that is safe as a one-tap button. The original job is never changed — a resize is saved as a new job.

The built-in patterns do not need resizing at all: they are drawn fresh at whatever panel size you type, with bridges sized for your plate from the start.

Resize a design and see the checks

Convert a design once, then resize it as often as you like. Previews and checks are free — you only pay when you take a DXF.

Open the app — first 5 files free

Common questions

Can I scale a DXF file without breaking it?

Yes, if you scale both directions by the same factor and re-check the design afterwards. Scaling changes every measurement, including the bridges between cuts, so a design that was safe at one size can be too thin at a smaller one.

Why did my design fail after I made it smaller?

Because the bridges shrank with it but the plate did not. A bridge must be at least 2× the plate thickness at any size, so a 6 mm bridge that was fine for 3 mm plate becomes a 3 mm bridge at half size — too thin to survive the cut.

My DXF opened far too small. What happened?

Most likely a units mix-up: a drawing made in inches read as millimetres comes out 25.4 times too small. Check the units the file declares and the units your software assumes when it opens the file.

Do bolt holes scale with the design?

They do if you scale the whole drawing, which is usually wrong: an M6 hole must stay 6.5 mm whatever size the part is. After resizing, set fixed-size holes and slots back to their real size.

Does KraftDXF re-check a design after resizing?

Yes. Every cutting check is measured again at the new size, anything too small to cut is listed, and a size that leaves the steel too thin for the plate is refused with the smallest safe size offered instead.