Guide
How Small Can You Cut With Plasma? Minimum Letter Size and Kerf
A letter survives plasma cutting when its strokes are at least twice the plate thickness, and its inside openings are wide enough to survive kerf taken from both sides, plus the heat. In practice that puts the minimum letter height at roughly 28 mm on 2 mm plate and about 42 mm on 3 mm plate. Below that, insides blow out and strokes melt back, however clean the file looks on screen.
Why small letters blow out
A small letter breaks two rules at once. The first is the bridge rule. Every stroke of a letter is a bridge: a strip of metal with a cut running down both sides. A strip thinner than twice the plate thickness overheats, melts back, or breaks. On 3 mm plate, a stroke under 6 mm is already at risk before anything else goes wrong.
The second is kerf. The plasma stream removes a slot of metal on every cut, and on a letter that slot is taken from both sides of every stroke and both sides of every inside opening. Plasma owners in the Langmuir Systems forum report kerf around 0.055 to 0.060 inch (about 1.4 to 1.5 mm) on common setups, and one owner cutting 0.3 inch stencil letters in 0.135 inch steel reported blowing out the whole inside of the letter. The inside of a small letter is only a few kerf-widths across, so the two cuts and their heat meet in the middle and the detail is gone.
The minimum stroke width for cut letters
The stroke is a bridge, so the bridge rule sets the floor, measured as the finished width after kerf has taken its share:
| Plate thickness | Minimum letter stroke |
|---|---|
| 1.5 mm | 3 mm |
| 2 mm | 4 mm |
| 3 mm | 6 mm |
| 5 mm | 10 mm |
Workshop experience points the same way. In the Langmuir forum's sign-design threads, the working answer is that at least 0.11 inch (about 2.8 mm) of metal is needed for a line to survive being cut from both sides, and stencil cutters recommend lines of at least 0.125 inch, preferably 0.15 inch (3.2 to 3.8 mm). Those numbers sit right where the bridge rule puts them for thin plate.
How tall can the letters be, at minimum?
Letter height follows from stroke width. In most bold sign fonts the stroke is roughly one seventh of the letter height, so the minimum height is roughly seven times the minimum stroke:
| Plate thickness | Minimum letter height (approx.) |
|---|---|
| 1.5 mm | 21 mm (0.8 inch) |
| 2 mm | 28 mm (1.1 inch) |
| 3 mm | 42 mm (1.7 inch) |
| 5 mm | 70 mm (2.8 inch) |
Treat these heights as starting estimates, not guarantees. Fonts differ: a bold stencil font carries thick strokes at small heights, while a thin script font fails at twice the size. The honest check is the stroke, not the height: measure the thinnest stroke in your actual font, at your actual size, and compare it with twice your plate thickness.
The insides of letters: openings and islands
The inside opening of a letter, the counter in an O, A, D or e, has to survive kerf from both sides plus heat built up in a small space. As a floor, an inside opening narrower than about twice your kerf is likely to close up or blow out. In practice, inside detail under about 3 mm across is where plasma owners report losing the inside of letters entirely.
The centre of a closed letter is also an island: a piece of metal held by nothing. Unless it is bridged, stencil style, it drops out the moment its outline finishes cutting. Small letters make this worse, because the bridges a centre needs are a visible share of the whole letter. A cut-ready file has its islands counted, and the only acceptable count of unbridged islands is zero.
Does laser cutting allow smaller letters than plasma?
Yes, somewhat. A laser's kerf is far narrower than a plasma stream's, so inside detail survives at smaller sizes and strokes lose less width to the cut. The bridge rule does not change, because it comes from plate thickness and heat, not from the machine. On the same plate, a laser holds finer inside detail, but a stroke under twice the plate thickness is still a weak strip of metal on either machine.
How to check a letter design before cutting
- Measure your kerf first. Cut a small test square, measure it against its drawn size, and the difference is your kerf. Nobody can guess it for you: it depends on your machine, your nozzle and your material.
- Measure the thinnest stroke in the design at its final size, and compare it with twice the plate thickness.
- Measure the smallest inside opening, and compare it with twice your kerf.
- Count the islands. Every closed letter centre must be bridged, or accepted as a fall-out before you start.
- Cut one test letter in scrap of the same plate, at the target size. One letter tells you more than any table, including this one.
The limits of these numbers
These minimums are floors, worked out from the bridge rule, from kerf arithmetic, and from what plasma owners report on their own machines. They are not guarantees. Amperage, cutting speed, consumable wear and material all move the real limit on a given day, and a skilled operator can sometimes nurse smaller detail through. What the numbers do reliably is warn you when a design asks for detail the plate and the process cannot hold, while the plate is still on the rack instead of smoking on the table.
KraftDXF measures every bridge in your file against your plate thickness, counts islands, applies your kerf at the exact size you enter, and lists every repair before you download.
Make/check your file free — first 5 files freeLetter size questions
How small can letters be on 2 mm plate?
About 28 mm tall, as a starting estimate. The rule behind it: on 2 mm plate the strokes must be at least 4 mm wide (twice the plate thickness), and in most bold sign fonts the stroke is roughly one seventh of the letter height. Measure the thinnest stroke in your actual font, not just the height.
Why do the insides of my letters blow out?
The inside opening is cut from both sides, so kerf is taken twice, and the heat of both cuts meets in a small space. Openings narrower than about twice your kerf, roughly 3 mm on a typical plasma setup, tend to close up or blow out. Plasma owners report exactly this on small stencil letters.
What is the minimum stroke width for plasma-cut letters?
Twice the plate thickness, measured as the finished width after kerf: 3 mm strokes on 1.5 mm plate, 4 mm on 2 mm, 6 mm on 3 mm, and 10 mm on 5 mm. A letter stroke is a bridge, a strip of metal with a cut on both sides, and the bridge rule sets its floor.
Does laser cutting allow smaller letters than plasma?
Somewhat. A laser's kerf is much narrower than a plasma stream's, so inside detail survives at smaller sizes. The bridge rule does not change, because it comes from plate thickness and heat: a stroke under twice the plate thickness is a weak strip of metal on either machine.
How do I check a letter design before cutting it?
Measure your kerf with a test square. Measure the thinnest stroke against twice the plate thickness, and the smallest inside opening against twice your kerf. Count the unbridged islands, the centres of closed letters. Then cut one test letter in scrap of the same plate before committing the full sign.
More guides: Minimum bridge width · Cut-ready DXF checklist · All guides